Table of Contents
Previous Chapter
Table of Contents
Previous Chapter
The AXAF-I CCD Imaging Spectrometer (ACIS) Science Instrument Software (SIS) is being developed by the Massachusetts Institute of Technology, Center for Space Research (MIT-CSR) as part of the ACIS Digital Processor Assembly (DPA). The DPA resides on-board the Advanced X-ray Astrophysics Facility - Imaging (AXAF-I). The DPA Science Instrument Software is responsible for acquiring and processing image data from the ACIS CCD Imaging Spectrometer and transferring the processed data to the AXAF-I Command and Telemetry Unit (CTU), which is then responsible for sending the information to the ground.
The ACIS Science Instrument Software Detailed Design Specification (Code-To) describes the design of the instrument software in sufficient detail to permit code development.
This document applies to the detailed design of the ACIS DPA Science Instrument Software. It does not provide information for the Ground Support Software (GSS), which is maintained separately as part of the Electronic Ground Support Equipment (EGSE).
This document supplies information applicable to SDM03 from the original contract, and to DM09 from MM8075.1.
By mutual agreement, MSFC Software Management and Development Requirements Manual MM8075.1, which supersedes MA-001-006-2H, forms the basis for this document.
This specification relies on a set of existing documentation. The following table lists these documents.
-----------------------------------------------------------------------------------------
Part Number Version Title
MSFC MM 8075.1 January 22, 1991 MSFC Software Management and Develop
ment Requirements Manual
MIT-CSR 36-01103 B ACIS Science Instrument Software Require
ments Specification
MIT-CSR 36-01502 04 ACIS Technical Analyses and Models: ACIS
Hardware Specification and System Descrip
tion
NU910701 1991 Nucleus RTX Reference Manual from Accel
erated Technology, Inc.
NU910702 1991 Nucleus RTX Internals Manual from Acceler
ated Technology, Inc.
ISBN 0-8053-5340-2 1994 Object-Oriented Analysis and Design with
Applications, Second Edition by Grady
Booch, Benjamin/Cummings
NASA Reference Publication, September, 1993 Mongoose ASIC Microcontroller Program
1319 ming Guide, Brian S. Smith, GSFC
ISBN 1-55860-297-6 1994 MIPS Programmer's Handbook by Erin
Farquahar and Philip Bunce, Morgan
Kaufman Publishers
ISBN 0-13-584749-4 1989 MIPS RISC Architecture, by Gerry Kane,
Prentice Hall
MIT 36-10410 TBD ACIS Instrument Protocol and Command List
MIT 36-02205 A DPA/DEA Interface Control Document
-----------------------------------------------------------------------------------------
This document assumes that readers will be familiar with the ACIS Contract End Item Specification, and the ACIS Science Instrument Software Requirements Specification.
This document assumes that there are no hardware nor operating system portability requirements on the instrument software design or implementation.
This document assumes that the Back End Processor software design is implemented in C++, and that the Front End Processor design is implemented in C. Unless otherwise specified, all data types and example code shown in this document use C++ notation.
This design assumes that the GNU C++ compiler, running on an DECstation 3000 or 5000, is used to compile the flight version of this software. Other compilers may be used for unit and integration testing portions of the software, but there may be parts of the software which are compiler specific.
Unless otherwise specified, diagrams and detailed class descriptions presented in this document use Booch Notation, as described in "Object-Oriented Analysis and Design with Applications," by Grady Booch, 1994.
Figure 1 illustrates the icons and associations this document uses to illustrate the relationships between class and structure definitions.
Figure 2 illustrates the icons and relationships this document uses to illustrate scenarios involving different objects (i.e. class instances).
FIGURE 2. Object Diagram Icons
All words and abbreviations of all class category names start with a capital letter. The remaining letters in each word of the name are in lower case. All words and abbreviations within the name shall contain at least two letters.
All names of class categories (i.e. subsystem) within this document are represented using bold, italicized Courier text:
ClassCategoryName
All words and abbreviations in all class, structure, enumeration, and union names start with a capital letter. The remaining letters in each word of the name are in lower case. All words and abbreviations within the name shall contain at least two letters.
All class names within this document are represented using bold Courier text:
ClassName
The first word or abbreviation in all function and member function names shall start with a lower-case letter. All remaining words, if any, within the name shall start with a capital letter. The remaining letters in each word of the name are in lower case. All words and abbreviations within the name shall contain at least two letters. All function argument names shall conform to the convention described for Variable Names (see Section 2.6.4 ).
Functions which suspend execution of the currently running process until some condition is satisfied shall contain the word "wait" embedded in their name. Functions which require some condition, but do not suspend the process shall contain the word "request" embedded in their name. Functions which contain an infinite loop, such as the main function of a process, shall have the word "go" contained within their name.
All function names are represented using plain Courier text:
functionName or functionName()
The first word or abbreviation in all function and member function names Shall start with a lower-case letter. All remaining words, if any, within the name may or may not start with a capital letter. The remaining letters in each word of the name are in lower case. All words and abbreviations within the name shall contain at least two letters.
All variables, instance variables and structure or enumeration tags are represented using italicized Courier text:
variableName
With the exception of the Boolean type, all letters in enumeration tag names are capitalized.
This document uses no special typographic convention for displaying enumeration tag values:
ENUMTAG (except for BoolTrue and BoolFalse, see Section 2.7 )
All preprocessor definitions are completely capitalized. Spaces may be indicated using underscores.
This document uses no special typographical convention for displaying preprocessor definitions:
PREPROCESSOR_DEFINITION
Except for filename extensions, all directories and filenames are in lower-case, with spaces represented as underscores. All C-language source and header files use the ".c" and ".h" extensions, respectively. All C++-language source and header files use the ".C" and ".H" extensions respectively. All assembler files have the ".s" extension.
This document uses no special typographical convention for displaying directory or filenames:
directory_name/filename.C
Given that there are no portability requirements on the ACIS software, unless otherwise specified, it assumes that all data elements have little-endian byte ordering. For example, the 32-bit value 0x12345678 is stored as bytes in RAM as follows:
--------------------------- Virtual Address Byte Value--------------------------- 0 0x78 1 0x56 2 0x34 3 0x12 ---------------------------
By convention, bits within a word are numbered with the least-significant bit as bit number 0. This is consistent with the "MIPS Programmers Reference Guide."
Unless otherwise specified, all signed values use two's complement representation.
Given that there are no portability requirements on the ACIS software, rather than provide renamed type definitions, the ACIS software assumes that the compiler defines its concrete data types as follows:
TABLE 2. Concrete Data Type Assumptions
---------------------------------------------------------------- C/C++ Type(s) Sign and Size---------------------------------------------------------------- char signed 8-bit value unsigned char unsigned 8-bit value short signed 16-bit value unsigned short unsigned 16-bit value int or long signed 32-bit value unsigned, unsigned int, or unsigned long unsigned 32-bit value all pointers unsigned 32-bit values enumerated types unsigned 32-bit values ----------------------------------------------------------------
In order to distinguish true and false arguments and return values from signed integers (int), the ACIS instrument software defines a Boolean data type using the following enumeration:
enum Boolean
{
BoolFalse = 0,
BoolTrue = 1
};
This type is used by the software whenever an argument or return type expresses a true or false expression. Since, in C and C++, enumerated types can be converted to an integer type by the compiler, these enumerated values are compatible with compiler generated relational expressions. NOTE: In C++, relational expressions, however, can not be converted to a Boolean type without an explicit cast or conversion.
For example:
Boolean result = BoolTrue;
if (result == (3<4)) /* ok, result is compared as an int */
{
}
result = (3<4); /* wrong, int not converted to Boolean */
result = (Boolean) (3<4); /* ok, explicit type cast */
The ACIS timestamp counter relies on the spacecraft-supplied 1.024 MHz clock. As such, all timestamp values are in units of 0.9765625 microseconds.
All timer tick references made within this document are in units of 100 milliseconds (the Back End Processor timer-tick period).
In object-oriented design, there are "objects" and "classes." A class refers to the equivalent of a data structure definition and a collection of functions which operate on this data structure. An object refers to a physical declaration of a class. For example, in "C" one can have a structure such as:
struct foo
{
int a;
};
struct foo is analogous to a class definition where as in declaration of one of these structures, such as in the case of:
struct foo bar
bar is analogous to an object declaration.
Within this document, the Architecture section describes the system primarily in terms of specific objects. Later portions of this document develop and describe the various classes within the Back End Processor software, and focus on the detailed behaviors of these classes.
The class descriptions in this document specify the lifetime of an instance of the class using two keywords:
The use of the word persistent is a little misleading, in that it implies that the state of an object may be retained across instrument resets. Although there are a few such items, this document uses the keyword to indicate objects which are created at startup, and which last until the instrument is reset. All instances of a persistent class must last for the duration of the program. Transient objects are those which are created and initialized as needed by the running program, and destroyed when they are no longer in use. Some objects defined from transient classes may exist for the lifetime of the program, and others may come and go as the program runs. Unlike most C++ programs, the ACIS instrument software does not use a global run-time memory heap in order to avoid heap fragmentation and other issues. The memory for transient objects is obtained from collections of memory buffers, or on the stack. The lifetime of an object allocated from a memory pool ends when the object's destructor is invoked, and its memory is released back to its pool. The lifetime of an object declared on the stack ends when the scope of the code block which declared it ends.
The class and function descriptions in this document specify the type of task and interrupt environment supported by the class or function, using three keywords:
In general, classes and functions used only during initialization, assume that only one thread of control is active, and specify Sequential. Classes and functions which expect to be used by only one task, or expect multiple tasks to arbitrate amongst themselves for access to the class or function, specify Guarded. Classes and functions which either do not require any inter-task arbitration (i.e. do not directly or indirectly modify any shared variable or hardware), or perform the arbitration internally, specify Synchronous.
Next Chapter